EZ100 Pull Line Blower

The Conduit Pull Line Blower EZ100 by Zeitler has been developed especially for network construction such as civil engineering, ground work, roads, tunnels, bridges, etc.

It is suitable for cable ducts from Ø 50 to 150 mm (internal diameter).

The pull line might be blown or aspirated. Water, small residues, impurities or else can often be pushed through with the shuttle in only one operation.

MADE IN SWITZERLAND

QUICK FACTS

Blow or suck pull line (tensile strength up to 300 kg) without a heavy compressor

For all commercial pipe work (internal diameter from 50 to 150 mm)

With special equipment also for small diameters from 25 mm

For all network construction such as civil engineering, ground work, roads, tunnels, bridges

For lengths of 1000 m and more (current record 2’850 m)

Huge time saver in conduit pull line blowing

Cleaning, taking water out, calibrating and conduit pull line blowing in one step

Excellent accessibility, even in confined spaces

Easy to handle

Double function (blowing and suction mode)

Perfect and strong to solve conduit pull line blowing problems

Suitable in any car boot

Power supply versions
115Volt/60Hz or 230V/50Hz

Perfect value for money and time saved

QUICK SETUP

Conduit ends must be clean and cut off evenly

firstly, blow in without shuttle, check if conduit penetrable/correct conduit

assemble shuttle corresponding exactly to the internal diameter of conduit

Insert pull line through pull line supply and knot it tightly to the shuttle

Place shuttle in the conduit and press EZ100 to the conduit, the front being movable for 360°

Blow shuttle through without interrupting

Attach either cable/s or extra strong pull line

Attach cable to pull line

SUCTION MODE AND DUCT CLEANING

Condensed water, surface water, small residues, impurities or else are often pushed through by the shuttle.

In certain situations switch to suction mode and suck the shuttle from the opposite end. Be careful not to aspirate water into the EZ100 Pull Line Blower

EZ100 CONDUIT PULL LINE BLOWER

Play Video

EZ100 BLOWING POWER unmatched

WHAT IS INCLUDED?

EZ100 - READY TO GO in a strong plastic carry case

EZ100 Stringing gun complete kit with change-over front in strong plastic case

2 special pull line rolls (ø 1 mm, tensile strength approx 24 kg,
length approx. 900 m)

1 Suction device

5 shuttle sets dimensions free of choice (ø 20-150 mm).
Each set completes 2 shuttles.

ZEITLER Conduit Pull Line Blowers

EZ100 Pull Line Blower

.cls-1{fill:red;}.cls-2{fill:#fff;}MADE IN SWITZERLAND

QUICK FACTS

Blow or suck pull line (tensile strength up to 300 kg) without a heavy compressor

For all commercial pipe work (internal diameter from 50 to 150 mm)

With special equipment also for small diameters from 25 mm

For all network construction such as civil engineering, ground work, roads, tunnels, bridges

For lengths of 1000 m and more (current record 2’850 m)

Huge time saver in conduit pull line blowing

Cleaning, taking water out, calibrating and conduit pull line blowing in one step

Excellent accessibility, even in confined spaces

Easy to handle

Double function (blowing and suction mode)

Perfect and strong to solve conduit pull line blowing problems

Suitable in any car boot

Power supply versions 115Volt/60Hz or 230V/50Hz

Perfect value for money and time saved

QUICK SETUP

Conduit ends must be clean and cut off evenly

firstly, blow in without shuttle, check if conduit penetrable/correct conduit

assemble shuttle corresponding exactly to the internal diameter of conduit

Insert pull line through pull line supply and knot it tightly to the shuttle

Place shuttle in the conduit and press EZ100 to the conduit, the front being movable for 360°

Blow shuttle through without interrupting

Attach either cable/s or extra strong pull line

Attach cable to pull line

SUCTION MODE AND DUCT CLEANING

Condensed water, surface water, small residues, impurities or else are often pushed through by the shuttle.

In certain situations switch to suction mode and suck the shuttle from the opposite end. Be careful not to aspirate water into the EZ100 Pull Line Blower

EZ100 CONDUIT PULL LINE BLOWER

EZ100 BLOWING POWER *unmatched*

WHAT IS INCLUDED?

EZ100 - READY TO GO in a strong plastic carry case

EZ100 Stringing gun complete kit with change-over front in strong plastic case

2 special pull line rolls (ø 1 mm, tensile strength approx 24 kg, length approx. 900 m)

1 Suction device

5 shuttle sets dimensions free of choice (ø 20-150 mm). Each set completes 2 shuttles.

1 box with assembly material for shuttles

1 Special equipment for small tube diameters

1 Foam adapter

1 parachute 30-60mm

1 parachute 60-100 mm

1 parachute 100-150 mm

1 Parachute (Ø 30-60 mm)

1 cone

1 Operating instructions

Request a personalized Price

EZ100 Conduit Pull Line Blower

.cls-1{fill:red;}.cls-2{fill:#fff;}MADE IN SWITZERLAND

FREE WORLDWIDE SHIPPING

Zeitler Pull Line Blower

EZ15

EZ50

EZ300

MADE IN SWITZERLAND

Power supply versions
115Volt/60Hz or 230V/50Hz

EZ100 BLOWING POWER unmatched

2 special pull line rolls (ø 1 mm, tensile strength approx 24 kg,
length approx. 900 m)

5 shuttle sets dimensions free of choice (ø 20-150 mm).
Each set completes 2 shuttles.

MADE IN SWITZERLAND

Zeitler
Pull Line Blower